Challenge the 200-301 exam with our free, forefront PDF and Exam Questions
Embark on an enlightening quest, surrounded by the ethereal glow of the 200-301 dumps. Like the ever-changing hues of a kaleidoscope, the 200-301 dumps display a spectrum of practice questions, each one more intriguing than the last. Whether the crystal-clear PDFs paint vivid mental images or the VCE format spins a captivating tale of success, the 200-301 dumps are your sherpa on this spiritual journey. An age-old tome of wisdom, the 200-301 dumps breathe life into arcane knowledge, ensuring no leaf remains unturned. In the sanctity of these resources, we chant our mantra of a 100% Pass Guarantee.
[Up-to-date Collection] Experience the 100% pass guarantee with the free 200-301 PDF and Exam Questions
Question 1:
What are two characteristics of a public cloud Implementation? (Choose two.)
A. It is owned and maintained by one party, but it is shared among multiple organizations.
B. It enables an organization to fully customize how It deploys network resources.
C. It provides services that are accessed over the Internet.
D. It Is a data center on the public Internet that maintains cloud services for only one company.
E. It supports network resources from a centralized third-party provider and privately-owned virtual resources
Correct Answer: CE
Question 2:
Which type does a port become when it receives the best BPDU on a bridge?
A. The designated port
B. The backup port
C. The alternate port
D. The root port
Correct Answer: D
Question 3:
Refer to the exhibit.
An engineer configured NAT translations and has verified that the configuration is correct. Which IP address is the source IP?
A. 10.4.4.4
B. 10.4.4.5
C. 172.23.103.10
D. 172.23.104.4
Correct Answer: D
The packet starts off with address 10.4.4.5 (Inside Local). It gets translated to 172.23.104.4 (Inside Global).
It\’s destination is 172.23.103.10 (Outside Global). It may get natted at the destination, but to the source NAT Engine it is still 172.23.103.10.
Question 4:
What is the difference in data transmission delivery and reliability between TCP and UDP?
A. TCP transmits data at a higher rate and ensures packet delivery. UDP retransmits lost data to ensure applications receive the data on the remote end.
B. UDP sets up a connection between both devices before transmitting data. TCP uses the three-way handshake to transmit data with a reliable connection.
C. UDP is used for multicast and broadcast communication. TCP is used for unicast communication and transmits data at a higher rate with error checking.
D. TCP requires the connection to be established before transmitting data. UDP transmits data at a higher rate without ensuring packet delivery.
Correct Answer: D
UDP speeds up transmissions by enabling the transfer of data before an agreement is provided by the receiving party. As a result, UDP is beneficial in time- sensitive communications, including voice over IP (VoIP), domain name system (DNS) lookup, and video or audio playback.
Question 5:
Refer to the exhibit.
An engineer just installed network 10.120.10.0/24. Which configuration must be applied to the R14 router to add the new network to its OSPF routing table?
A. Router ospf 100 Network 10.120.10.0 0.0.0.255 area 0
B. Router ospf 120 Network 10.120.10.0 255.255.255.0 area 0 Ip route 10.120.10.0 255.255.255.0 fa0/1
C. Router ospf 100 area 0 Network 10.120.10.0 0.0.0.255
D. Router ospf 100 Network 10.120.10.0 255.255.255.0 area 0
Correct Answer: A
Question 6:
Which interface is used for out-of-band management on a WLC?
A. management
B. virtual
C. dynamic
D. service port
Correct Answer: D
Out of band is service-port interface In band is management interface
Question 7:
Refer to the exhibit. Routers R1 and R3 have the default configuration The router R2 priority is set to 99 Which commands on R3 configure it as the DR in the 10.0 4.0/24 network?
A. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 100
B. R3(config)#interface Gig0/0 R3(config-if)#ip ospf priority 100
C. R3(config)#interface Gig0/0 R3(config-if)i=ip ospf priority 1
D. R3(config)#interface Gig0/1 R3(config-if)#ip ospf priority 0
Correct Answer: B
Question 8:
What does the implementation of a first-hop redundancy protocol protect against on a network?
A. root-bridge loss
B. spanning-tree loops
C. default gateway failure
D. BGP neighbor flapping
Correct Answer: C
Question 9:
A network engineer implements a new Cisco Firepower device on the network to take advantage of its intrusion detection functionality. There is a requirement to analyze the traffic going across the device, alert on any malicious traffic, and appear as a bump in the wire. How should this be implemented?
A. Specify the BVI IP address as the default gateway for connected devices
B. Enable routing on the Cisco Firepower
C. Add an IP address to the physical Cisco Firepower interfaces
D. Configure a bridge group in transparent mode
Correct Answer: D
Question 10:
What is a requirement when configuring or removing LAG on a WLC?
A. The Incoming and outgoing ports for traffic flow must be specified If LAG Is enabled.
B. The controller must be rebooted after enabling or reconfiguring LAG.
C. The management interface must be reassigned if LAG disabled.
D. Multiple untagged interfaces on the same port must be supported.
Correct Answer: B
When you enable LAG or make any changes to the LAG configuration, you must immediately reboot the controller.
Question 11:
Refer to the exhibit.
Which command provides this output?
A. show ip route
B. show cdp neighbor
C. show ip interface
D. show interface
Correct Answer: B
Question 12:
Refer to the exhibit.
What does apple represent within the JSON data?
A. array
B. object
C. number
D. string
Correct Answer: D
https://restfulapi.net/json-data-types/
Question 13:
Refer to the exhibit.
Which two values does router R1 use to determine the best path to reach destinations in network 1,0.0.0/8? (Choose two.)
A. longest prefix match
B. highest administrative distance
C. highest metric
D. lowest metric
E. lowest cost to reach the next hop
Correct Answer: BE
The two values that router R1 uses to identify valid routes for the R3 loopback address 1.1.1.3/32 are:
Lowest cost to reach the next hop: Router R1 will look for the route with the lowest cost to reach the next hop, as determined by the routing protocol being used. This is typically the metric or cost associated with the path to the next hop.
Lowest administrative distance: If there are multiple routes with the same cost, router R1 will use the administrative distance to determine the best path. The administrative distance is a value assigned to each routing protocol that indicates
the reliability of the routing information. A lower administrative distance indicates a more reliable source of routing information.
Question 14:
Refer to the exhibit.
What is represented by the word “switch\’\’ in line 2 of the JSON schema?
A. array
B. key
C. value
D. object
Correct Answer: C
Question 15:
Which component controls and distributes physical resources for each virtual machine?
A. hypervisor
B. OS
C. CPU
D. physical enclosure
Correct Answer: A