Free Providing CertBus Cisco 400-101 VCE Exam Study Guides With New Update Exam Questions
CertBus 2017 Real Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!
☆ 400-101 CCIE Exam PDF and VCE Dumps : 828QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2017 Real 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing
Following 400-101 828QAs are all new published by Cisco Official Exam Center
There is no need to worry about the difficulties on the CCIE Newest 400-101 QAs exam preparation. CertBus will assist you pass your CCIE Newest 400-101 pdf exam with up to date Hotest 400-101 pdf CCIE Routing and Switching Written v5.0 PDF and VCE dumps. CertBus provides the most update real CCIE Hotest 400-101 vce exam preparation material, covering each and every aspect which real CCIE Sep 24,2017 Hotest 400-101 pdf dumps exam requires. We ensure you 100% success in CCIE Hotest 400-101 free download exam.
CertBus 400-101 certification exam portal. CertBus – 100% real 400-101 certification exam questions and answers. easily pass with a high score. CertBus – clear all your 400-101 certification exams with CertBus study guide. 100% pass rate and money back guarantee. CertBus 400-101 certification questions. CertBus – help you to pass all 400-101 certification exams!
We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html
QUESTION NO:1
Which two commands are required to enable multicast on a router, knowing that the receivers only
support IGMPv2? (Choose two.)
A. ip pim rp-address
B. ip pim ssm
C. ip pim sparse-mode
D. ip pim passive
Answer: A,C
Explanation:
Sparse mode logic (pull mode) is the opposite of Dense mode logic (push mode), in Dense mode
it is supposed that in every network there is someone who is requesting the multicast traffic so
PIM-DM routers begin by flooding the multicast traffic out of all their interfaces except those from
where a prune message is received to eliminate the
QUESTION NO:2
A branch router is configured with an egress QoS policy that was designed for a total number of
10 concurrent VOIP calls.
Due to expansion, 15 VOIP calls are now running over the link, but after the 14th call was
established, all calls were affected and the voice quality was dramatically degraded.
Assuming that there is enough bandwidth on the link for all of this traffic, which part of the QoS
configuration should be updated due to the new traffic profile?
A. Increase the shaping rate for the priority queue. B.
Remove the policer applied on the priority queue. C.
Remove the shaper applied on the priority queue. D.
Increase the policing rate for the priority queue.
Answer: D
Explanation:
QUESTION NO:3
A new backup connection is being deployed on a remote site router. The stability of the connection
has been a concern. In order to provide more information to EIGRP regarding this interface, you
wish to incorporate the “reliability” cost metric in the EIGRP calculation with the command metric
weights 1 0 1 0 1.
What impact will this modification on the remote site router have for other existing EIGRP
neighborships from the same EIGRP domain?
A. Existing neighbors will immediately begin using the new metric.
B. Existing neighbors will use the new metric after clearing the EIGRP neighbors.
C. Existing neighbors will resync, maintaining the neighbor relationship.
D. All existing neighbor relationships will go down.
Answer: D
Explanation:
QUESTION NO:4
Refer to the exhibit.
R1 has an EBGP session to ISP 1 and an EBGP session to ISP 2. R1 receives the same prefixes
through both links.
Which configuration should be applied so that the link between R1 and ISP 2 will be preferred for
outgoing traffic (R1 to ISP 2)?
A. Increase local preference on R1 for received routes
B. Decrease local preference on R1 for received routes
C. Increase MED on ISP 2 for received routes
D. Decrease MED on ISP 2 for received routes
Answer: A
Explanation: Explanation
Local preference is an indication to the AS about which path has preference to exit the AS in order
to reach a certain network. A path with higher local preference is preferred more. The default value
of preference is 100.
Reference
http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080b82d1f.s
html?
referring_site=smartnavRD
QUESTION NO:6
Why would a rogue host that is running a DHCP server on a campus LAN network present a
security risk?
A. It may allocate IP addresses from an unknown subnet to the users.
B. All multicast traffic can be sniffed by using the DHCP multicast capabilities.
C. The CPU utilization of the first hop router can be overloaded by exploiting DHCP relay open
ports.
D. A potential man-in-the-middle attack can be used against the clients.
Answer: D
Explanation:
Latest 400-101 Dumps400-101 Study Guide400-101 Exam Questions
QUESTION NO:7
Which statement is true about TCN propagation?
A. The originator of the TCN immediately floods this information through the network.
B. The TCN propagation is a two step process.
C. A TCN is generated and sent to the root bridge.
D. The root bridge must flood this information throughout the network.
Answer: C
Explanation:
Explanation
New Topology Change Mechanisms
When an 802.1D bridge detects a topology change, it uses a reliable mechanism to first notify the
root bridge.
This is shown in this diagram:
Once the root bridge is aware of a change in the topology of the network, it sets the TC flag on the
BPDUs it sends out, which are then relayed to all the bridges in the network. When a bridge
receives a BPDU with the TC flag bit set, it reduces its bridging-table aging time to forward delay
seconds. This ensures a relatively quick flush of stale information. Refer to Understanding
Spanning-Tree Protocol Topology Changes for more information on this process. This topology
change mechanism is deeply remodeled in RSTP. Both the detection of a topology change and its
propagation through the network evolve.
Topology Change Detection
In RSTP, only non-edge ports that move to the forwarding state cause a topology change. This
means that a loss of connectivity is not considered as a topology change any more, contrary to
802.1D (that is, a port that moves to blocking no longer generates a TC). When a RSTP bridge
detects a topology change, these occur:
It starts the TC While timer with a value equal to twice the hello-time for all its non-edge
designated ports and its root port, if necessary.
It flushes the MAC addresses associated with all these ports.
Note: As long as the TC While timer runs on a port, the BPDUs sent out of that port have the TC
bit set.
BPDUs are also sent on the root port while the timer is active.
Topology Change Propagation
When a bridge receives a BPDU with the TC bit set from a neighbor, these occur:
It clears the MAC addresses learned on all its ports, except the one that receives the topology
change.
It starts the TC While timer and sends BPDUs with TC set on all its designated ports and root port
(RSTP no longer uses the specific TCN BPDU, unless a legacy bridge needs to be notified).
This way, the TCN floods very quickly across the whole network. The TC propagation is now a one
step process. In fact, the initiator of the topology change floods this information throughout the
network, as opposed to 802.1D where only the root did. This mechanism is much faster than the
802.1D equivalent. There is no need to wait for the root bridge to be notified and then maintain the
topology change state for the whole network for seconds.
In just a few seconds, or a small multiple of hello-times, most of the entries in the CAM tables of
the entire network (VLAN) flush. This approach results in potentially more temporary flooding, but
on the other hand it clears potential stale information that prevents rapid connectivity restitution.
Reference
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml
QUESTION NO:9
Which two are effects of connecting a network segment that is running 802.1D to a network
segment that is running 802.1w? (Choose two.)
A. The entire network switches to 802.1D and generates BPDUs to determine root bridge status. B.
A migration delay of three seconds occurs when the port that is connected to the 802.1D bridge
comes up.
C. The entire network reconverges and a unique root bridge for the 802.1D segment, and a root
bridge for the 802.1w segment, is chosen.
D. The first hop 802.1w switch that is connected to the 802.1D runs entirely in 802.1D compatibility
mode and converts the BPDUs to either 802.1D or 802.1w BPDUs to the 802.1D or 802.1w
segments of the network.
E. Classic 802.1D timers, such as forward delay and max-age, will only be used as a backup, and
will not be necessary if point-to-point links and edge ports are properly identified and set by the
administrator.
Answer: B,E
Explanation:
Each port maintains a variable that defines the protocol to run on the corresponding segment. A
migration delay timer of three seconds also starts when the port comes up. When this timer runs,
the current STP or RSTP mode associated to the port is locked. As soon as the migration delay
expires, the port adapts to the mode that corresponds to the next BPDU it receives. If the port
changes its mode of operation as a result of a BPDU received, the migration delay restarts.
802.1D works by the concept that the protocol had to wait for the network to converge before it
transitioned a port into the forwarding state. With Rapid Spanning Tree it does not have to rely on
any timers, the only variables that that it relies on is edge ports and link types.
Any uplink port that has an alternate port to the root can be directly placed into the forwarding
state (This is the Rapid convergence that you speak of “restored quickly when RSTP is already in
use?”). This is what happened when you disconnected the primary look; the port that was ALT,
moved to FWD immediately, but the switch also still needs to create a BDU with the TC bit set to
notify the rest of the network that a topology has occurred and all non-edge designated ports will
transition to BLK, LRN, and then FWD to ensure there are no loops in the rest of the network. This
is why if you have a host on a switchport, and you know for a fact that it is only one host, enable
portfast to configure the port as an edgeport so that it does not have to transition to all the STP
states.
Reference
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml
QUESTION NO:15
Which three options are considered in the spanning-tree decision process? (Choose three.)
A. lowest root bridge ID
B. lowest path cost to root bridge
C. lowest sender bridge ID
D. highest port ID
E. highest root bridge ID
F. highest path cost to root bridge
Answer: A,B,C
Explanation:
Configuration bridge protocol data units (BPDUs) are sent between switches for each port.
Switches use s four step process to save a copy of the best BPDU seen on every port. When a
port receives a better BPDU, it stops sending them. If the BPDUs stop arriving for 20 seconds
(default), it begins sending them again.
Step 1 Lowest Root Bridge ID (BID)
Step 2 Lowest Path Cost to Root Bridge
Step 3 Lowest Sender BID
Step 4 Lowest Port ID
Reference
Cisco General Networking Theory Quick Reference Sheets
QUESTION NO:21
Refer to the exhibit.
A packet from RTD with destination RTG, is reaching RTB. What is the path this packet will take
from RTB to reach RTG?
A. RTB – RTA – RTG
B. RTB – RTD – RTC – RTA – RTG
C. RTB – RTF – RTE – RTA – RTG
D. RTB will not be able to reach RTG since the OSPF configuration is wrong.
Answer: C
Explanation:
QUESTION NO:26
Refer to the exhibit.
Why is AS 65333 in parentheses?
A. It is an external AS.
B. It is a confederation AS.
C. It is the AS of a route reflector.
D. It is our own AS.
E. A route map has been applied to this route.
F. The BGP next hop is unreachable.
Answer: B
Explanation:
CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.
400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing
400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]
Why select/choose CertBus?
Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.