Free Sharing CertBus Updated Cisco 400-101 VCE and PDF Exam Practice Materials

10/17/2018|

Categories :

CertBus 2018 Valid Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!

☆ 400-101 CCIE Exam PDF and VCE Dumps : 1379QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2018 Valid 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

Following 400-101 1379QAs are all new published by Cisco Official Exam Center

This dump is 100% valid to pass Cisco CCIE Newest 400-101 free download exam. The only tips is please do not just memorize the questions and answers, you need to get through understanding of it because the question changed a little in the real exam. Follow the instructions in the CertBus CCIE Oct 17,2018 Hotest 400-101 study guide CCIE Routing and Switching Written v5.0 PDF and VCEs. All CertBus materials will help you pass your Cisco CCIE exam successfully.

the CertBus 400-101exam | pass the 400-101 exam on your first try! CertBus 100% accurate exam brain dumps with latest update. download the free 400-101 demo to check first. CertBus – best 400-101 training and certification computer-based-training online resources. CertBus expert team is will help you to get all 400-101 certifications easily.

We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html

QUESTION NO:1

Which two commands are required to enable multicast on a router, knowing that the receivers only

support IGMPv2? (Choose two.)

A. ip pim rp-address

B. ip pim ssm

C. ip pim sparse-mode

D. ip pim passive

Answer: A,C

Explanation:

Sparse mode logic (pull mode) is the opposite of Dense mode logic (push mode), in Dense mode

it is supposed that in every network there is someone who is requesting the multicast traffic so

PIM-DM routers begin by flooding the multicast traffic out of all their interfaces except those from

where a prune message is received to eliminate the

QUESTION NO:4

Refer to the exhibit.

R1 has an EBGP session to ISP 1 and an EBGP session to ISP 2. R1 receives the same prefixes

through both links.

Which configuration should be applied so that the link between R1 and ISP 2 will be preferred for

outgoing traffic (R1 to ISP 2)?

A. Increase local preference on R1 for received routes

B. Decrease local preference on R1 for received routes

C. Increase MED on ISP 2 for received routes

D. Decrease MED on ISP 2 for received routes

Answer: A

Explanation: Explanation

Local preference is an indication to the AS about which path has preference to exit the AS in order

to reach a certain network. A path with higher local preference is preferred more. The default value

of preference is 100.

Reference

http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080b82d1f.s

html?

referring_site=smartnavRD

QUESTION NO:5

Refer to the exhibit.

A small enterprise connects its office to two ISPs, using separate T1 links. A static route is used

for the default route, pointing to both interfaces with a different administrative distance, so that one

of the default routes is preferred.

Recently the primary link has been upgraded to a new 10 Mb/s Ethernet link.

After a few weeks, they experienced a failure. The link did not pass traffic, but the primary static

route remained active. They lost their Internet connectivity, even though the backup link was

operating.

Which two possible solutions can be implemented to avoid this situation in the future? (Choose

two.)

A. Implement HSRP link tracking on the branch router R1.

B. Use a track object with an IP SLA probe for the static route on R1.

C. Track the link state of the Ethernet link using a track object on R1.

D. Use a routing protocol between R1 and the upstream ISP.

Answer: B,D

Explanation:

Interface Tracking

Interface tracking allows you to specify another interface on the router for the HSRP process to

monitor in order to alter the HSRP priority for a given group.

If the specified interface’s line protocol goes down, the HSRP priority of this router is reduced,

allowing another HSRP router with higher priority can become active (if it has preemption

enabled).

To configure HSRP interface tracking, use the standby [group] track interface [priority] command.

When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you

explicitly set the decrement value, then the value is decreased by that amount if that interface is

down, and decrements are cumulative. If you do not set an explicit decrement value, then the

value is decreased by 10 for each interface that goes down, and decrements are cumulative.

The following example uses the following configuration, with the default decrement value of 10.

Note: When an HSRP group number is not specified, the default group number is group 0.

interface ethernet0

ip address 10.1.1.1 255.255.255.0

standby ip 10.1.1.3

standby priority 110

standby track serial0

standby track serial1

The HSRP behavior with this configuration is:

0 interfaces down = no decrease (priority is 110)

1 interface down = decrease by 10 (priority becomes100)

2 interfaces down = decrease by 10 (priority becomes 90)

Reference

http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml#i

ntracking

QUESTION NO:7

Which statement is true about TCN propagation?

A. The originator of the TCN immediately floods this information through the network.

B. The TCN propagation is a two step process.

C. A TCN is generated and sent to the root bridge.

D. The root bridge must flood this information throughout the network.

Answer: C

Explanation:

Explanation

New Topology Change Mechanisms

When an 802.1D bridge detects a topology change, it uses a reliable mechanism to first notify the

root bridge.

This is shown in this diagram:

Once the root bridge is aware of a change in the topology of the network, it sets the TC flag on the

BPDUs it sends out, which are then relayed to all the bridges in the network. When a bridge

receives a BPDU with the TC flag bit set, it reduces its bridging-table aging time to forward delay

seconds. This ensures a relatively quick flush of stale information. Refer to Understanding

Spanning-Tree Protocol Topology Changes for more information on this process. This topology

change mechanism is deeply remodeled in RSTP. Both the detection of a topology change and its

propagation through the network evolve.

Topology Change Detection

In RSTP, only non-edge ports that move to the forwarding state cause a topology change. This

means that a loss of connectivity is not considered as a topology change any more, contrary to

802.1D (that is, a port that moves to blocking no longer generates a TC). When a RSTP bridge

detects a topology change, these occur:

It starts the TC While timer with a value equal to twice the hello-time for all its non-edge

designated ports and its root port, if necessary.

It flushes the MAC addresses associated with all these ports.

Note: As long as the TC While timer runs on a port, the BPDUs sent out of that port have the TC

bit set.

BPDUs are also sent on the root port while the timer is active.

Topology Change Propagation

When a bridge receives a BPDU with the TC bit set from a neighbor, these occur:

It clears the MAC addresses learned on all its ports, except the one that receives the topology

change.

It starts the TC While timer and sends BPDUs with TC set on all its designated ports and root port

(RSTP no longer uses the specific TCN BPDU, unless a legacy bridge needs to be notified).

This way, the TCN floods very quickly across the whole network. The TC propagation is now a one

step process. In fact, the initiator of the topology change floods this information throughout the

network, as opposed to 802.1D where only the root did. This mechanism is much faster than the

802.1D equivalent. There is no need to wait for the root bridge to be notified and then maintain the

topology change state for the whole network for seconds.

In just a few seconds, or a small multiple of hello-times, most of the entries in the CAM tables of

the entire network (VLAN) flush. This approach results in potentially more temporary flooding, but

on the other hand it clears potential stale information that prevents rapid connectivity restitution.

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml

QUESTION NO:9

Which two are effects of connecting a network segment that is running 802.1D to a network

segment that is running 802.1w? (Choose two.)

A. The entire network switches to 802.1D and generates BPDUs to determine root bridge status. B.

A migration delay of three seconds occurs when the port that is connected to the 802.1D bridge

comes up.

C. The entire network reconverges and a unique root bridge for the 802.1D segment, and a root

bridge for the 802.1w segment, is chosen.

D. The first hop 802.1w switch that is connected to the 802.1D runs entirely in 802.1D compatibility

mode and converts the BPDUs to either 802.1D or 802.1w BPDUs to the 802.1D or 802.1w

segments of the network.

E. Classic 802.1D timers, such as forward delay and max-age, will only be used as a backup, and

will not be necessary if point-to-point links and edge ports are properly identified and set by the

administrator.

Answer: B,E

Explanation:

Each port maintains a variable that defines the protocol to run on the corresponding segment. A

migration delay timer of three seconds also starts when the port comes up. When this timer runs,

the current STP or RSTP mode associated to the port is locked. As soon as the migration delay

expires, the port adapts to the mode that corresponds to the next BPDU it receives. If the port

changes its mode of operation as a result of a BPDU received, the migration delay restarts.

802.1D works by the concept that the protocol had to wait for the network to converge before it

transitioned a port into the forwarding state. With Rapid Spanning Tree it does not have to rely on

any timers, the only variables that that it relies on is edge ports and link types.

Any uplink port that has an alternate port to the root can be directly placed into the forwarding

state (This is the Rapid convergence that you speak of “restored quickly when RSTP is already in

use?”). This is what happened when you disconnected the primary look; the port that was ALT,

moved to FWD immediately, but the switch also still needs to create a BDU with the TC bit set to

notify the rest of the network that a topology has occurred and all non-edge designated ports will

transition to BLK, LRN, and then FWD to ensure there are no loops in the rest of the network. This

is why if you have a host on a switchport, and you know for a fact that it is only one host, enable

portfast to configure the port as an edgeport so that it does not have to transition to all the STP

states.

Reference

http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml

Latest 400-101 Dumps 400-101 PDF Dumps 400-101 Braindumps

QUESTION NO:14

Which three options are features of VTP version 3? (Choose three.)

A. VTPv3 supports 8K VLANs.

B. VTPv3 supports private VLAN mapping.

C. VTPv3 allows for domain discovery.

D. VTPv3 uses a primary server concept to avoid configuration revision issues.

E. VTPv3 is not compatible with VTPv1 or VTPv2.

F. VTPv3 has a hidden password option.

Answer: B,D,F

Explanation:

Key Benefits of VTP Version 3

Much work has gone into improving the usability of VTP version 3 in three major areas:

The new version of VTP offers better administrative control over which device is allowed to update

other devices’ view of the VLAN topology. The chance of unintended and disruptive changes is

significantly reduced, and availability is increased. The reduced risk of unintended changes will

ease the change process and help speed deployment.

Functionality for the VLAN environment has been significantly expanded. Two enhancements are

most beneficial for today’s networks:

QUESTION NO:15

Which three options are considered in the spanning-tree decision process? (Choose three.)

A. lowest root bridge ID

B. lowest path cost to root bridge

C. lowest sender bridge ID

D. highest port ID

E. highest root bridge ID

F. highest path cost to root bridge

Answer: A,B,C

Explanation:

Configuration bridge protocol data units (BPDUs) are sent between switches for each port.

Switches use s four step process to save a copy of the best BPDU seen on every port. When a

port receives a better BPDU, it stops sending them. If the BPDUs stop arriving for 20 seconds

(default), it begins sending them again.

Step 1 Lowest Root Bridge ID (BID)

Step 2 Lowest Path Cost to Root Bridge

Step 3 Lowest Sender BID

Step 4 Lowest Port ID

Reference

Cisco General Networking Theory Quick Reference Sheets

QUESTION NO:17

Which three combinations are valid LACP configurations that will set up a channel? (Choose

three.)

A. On/On

B. On/Auto

C. Passive/Active

D. Desirable/Auto

E. Active/Active

F. Desirable/Desirable

Answer: A,C,E

Explanation:

QUESTION NO:18

Refer to the exhibit.

Which statement is correct about the prefix 160.0.0.0/8?

A. The prefix has encountered a routing loop.

B. The prefix is an aggregate with an as-set.

C. The prefix has been aggregated twice, once in AS 100 and once in AS 200.

D. None of these statements is true.

Answer: B

Explanation:

QUESTION NO:28

Which two orders in the BGP Best Path Selection process are correct? (Choose two.)

A. Higher local preference, then lowest MED, then eBGP over iBGP paths

B. Higher local preference, then highest weight, then lowest router ID

C. Highest weight, then higher local preference, then shortest AS path

D. Lowest origin type, then higher local preference, then lowest router ID

E. Highest weight, then higher local preference, then highest MED

Answer: A,C

Explanation:

CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.

400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.



Brand	Certbus	Testking	Pass4sure	Actualtests	Others
Price	$45.99	$124.99	$125.99	$189	$69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection