Free Sharing CertBus Updated Cisco 400-101 VCE and PDF Exam Practice Materials

CertBus 2018 Latest Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!

☆ 400-101 CCIE Exam PDF and VCE Dumps : 1379QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2018 Latest 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

Following 400-101 1379QAs are all new published by Cisco Official Exam Center

CCIE Aug 02,2018 Hotest 400-101 vce easy pass guidance: Preparing for Cisco CCIE Latest 400-101 study guide exam is really a tough task to achieve. However, CertBus provides the most comprehensive PDF and VCEs, covering each knowledge points required in the actual Latest 400-101 practice exam.

CertBus | 400-101 certification materials | videos | study guides. 4,500 exam dumps: pass your 400-101 certification exam with CertBus. CertBus: 400-101 certification preparation site. CertBus – leading provider of latest 400-101 certification exam study materials. try to download the free demo. CertBus 400-101 certification exam portal.

We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html

QUESTION NO:2

A branch router is configured with an egress QoS policy that was designed for a total number of

10 concurrent VOIP calls.

Due to expansion, 15 VOIP calls are now running over the link, but after the 14th call was

established, all calls were affected and the voice quality was dramatically degraded.

Assuming that there is enough bandwidth on the link for all of this traffic, which part of the QoS

configuration should be updated due to the new traffic profile?

A. Increase the shaping rate for the priority queue. B.

Remove the policer applied on the priority queue. C.

Remove the shaper applied on the priority queue. D.

Increase the policing rate for the priority queue.

Answer: D

Explanation:

QUESTION NO:4

Refer to the exhibit.

R1 has an EBGP session to ISP 1 and an EBGP session to ISP 2. R1 receives the same prefixes

through both links.

Which configuration should be applied so that the link between R1 and ISP 2 will be preferred for

outgoing traffic (R1 to ISP 2)?

A. Increase local preference on R1 for received routes

B. Decrease local preference on R1 for received routes

C. Increase MED on ISP 2 for received routes

D. Decrease MED on ISP 2 for received routes

Answer: A

Explanation: Explanation

Local preference is an indication to the AS about which path has preference to exit the AS in order

to reach a certain network. A path with higher local preference is preferred more. The default value

of preference is 100.

Reference

http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080b82d1f.s

html?

referring_site=smartnavRD

QUESTION NO:5

Refer to the exhibit.

A small enterprise connects its office to two ISPs, using separate T1 links. A static route is used

for the default route, pointing to both interfaces with a different administrative distance, so that one

of the default routes is preferred.

Recently the primary link has been upgraded to a new 10 Mb/s Ethernet link.

After a few weeks, they experienced a failure. The link did not pass traffic, but the primary static

route remained active. They lost their Internet connectivity, even though the backup link was

operating.

Which two possible solutions can be implemented to avoid this situation in the future? (Choose

two.)

A. Implement HSRP link tracking on the branch router R1.

B. Use a track object with an IP SLA probe for the static route on R1.

C. Track the link state of the Ethernet link using a track object on R1.

D. Use a routing protocol between R1 and the upstream ISP.

Answer: B,D

Explanation:

Interface Tracking

Interface tracking allows you to specify another interface on the router for the HSRP process to

monitor in order to alter the HSRP priority for a given group.

If the specified interface’s line protocol goes down, the HSRP priority of this router is reduced,

allowing another HSRP router with higher priority can become active (if it has preemption

enabled).

To configure HSRP interface tracking, use the standby [group] track interface [priority] command.

When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you

explicitly set the decrement value, then the value is decreased by that amount if that interface is

down, and decrements are cumulative. If you do not set an explicit decrement value, then the

value is decreased by 10 for each interface that goes down, and decrements are cumulative.

The following example uses the following configuration, with the default decrement value of 10.

Note: When an HSRP group number is not specified, the default group number is group 0.

interface ethernet0

ip address 10.1.1.1 255.255.255.0

standby ip 10.1.1.3

standby priority 110

standby track serial0

standby track serial1

The HSRP behavior with this configuration is:

0 interfaces down = no decrease (priority is 110)

1 interface down = decrease by 10 (priority becomes100)

2 interfaces down = decrease by 10 (priority becomes 90)

Reference

http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a91.shtml#i

ntracking

QUESTION NO:22

Refer to the exhibit.

Which path is selected as best path?

A. path 1, because it is learned from IGP B.

path 1, because the metric is the lowest C.

path 2, because it is external

D. path 2, because it has the higher router ID

Answer: B

Explanation:

QUESTION NO:26

Refer to the exhibit.

Why is AS 65333 in parentheses?

A. It is an external AS.

B. It is a confederation AS.

C. It is the AS of a route reflector.

D. It is our own AS.

E. A route map has been applied to this route.

F. The BGP next hop is unreachable.

Answer: B

Explanation:

400-101 PDF Dumps400-101 VCE Dumps400-101 Exam Questions

QUESTION NO:27

Refer to the exhibit.

What triggered the first SPF recalculation?

A. changes in a router LSA, subnet LSA, and external LSA

B. changes in a router LSA, summary network LSA, and external LSA

C. changes in a router LSA, summary network LSA, and summary ASBR LSA

D. changes in a router LSA, summary ASBR LSA, and external LSA

Answer: B

Explanation:

OSPFv2

Is built around links, and any IP prefix change in an area will trigger a full SPF. It advertises IP

information in Router and Network LSAs. The routers thus, advertise both the IP prefix information

(or the connected subnet information) and topology information in the same LSAs. This implies

that if an IP address attached to an interface changes, OSPF routers would have to originate a

Router LSA or a Network LSA, which btw also carries the topology information. This would trigger

a full SPF on all routers in that area, since the same LSAs are flooded to convey topological

change information. This can be an issue with an access router or the one sitting at the edge,

since many stub links can change regularly.

Only changes in interarea, external and NSSA routes result in partial SPF calculation (since type

3, 4, 5 and 7 LSAs only advertise IP prefix information) and thus IS-IS

QUESTION NO:30

What is the flooding scope of an OSPFv3 LSA, if the value of the S2 bit is set to 1 and the S1 bit is

set to 0?

A. link local

B. area wide

C. AS wide

D. reserved

Answer: C

Explanation:

The Type 1 router LSA is now link local and the Type 2 Network LSA is AS Wide

S2 and S1 indicate the LSA’s flooding scope. Table 9-1 shows the possible values of these two

bits and the associated flooding scopes.

Table 9-1 S bits in the OSPFv3 LSA Link State Type field and their associated flooding scopes

LSA Function Code, the last 13 bits of the LS Type field, corresponds to the OSPFv2 Type field.

Table 9-2 shows the common LSA types used by OSPFv3 and the values of their corresponding

LS Types. If you decode the hex values, you will see that the default U bit of all of them is 0. The S

bits of all LSAs except two indicate area scope. Of the remaining two, AS External LSAs have an

AS flooding scope and Link LSAs have a linklocal flooding scope. Most of the OSPFv3 LSAs have

functional counterparts in OSPFv2; these OSPFv2 LSAs and their types are also shown in Table

9-2.

Table 9-2 OSPFv3 LSA types and their OSPFv2 counterparts

Reference

http://www.networkworld.com/subnets/cisco/050107-ch9-ospfv3.html?page=1

QUESTION NO:33

Which two OSPF LSA types are new in OSPF version 3? (Choose two.)

A. Link

B. NSSA external

C. Network link

D. Intra-area prefix

E. AS domain

Answer: A,D

Explanation:

New LSA Types

OSPFv3 carries over the seven basic LSA types we’re familiar with from OSPFv2. However, the

type 1 and 2 LSAs have been re-purposed, as will be discussed in a bit. OSPFv3 also introduces

two new LSA types: Link and Intra-area Prefix.

Reference

http://packetlife.net/blog/2010/mar/2/ospfv2-versus-ospfv3/

QUESTION NO:34

In order to maintain security, with which hop count are IPv6 neighbor discovery packets sent?

A. 0

B. 1

C. 255

D. 256

Answer: C

Explanation:

QUESTION NO:37

Which command can be used on a PE router to connect to a CE router (11.1.1.4) in VRF red?

A. telnet 11.1.1.4 /vrf-source red

B. telnet 11.1.1.4 source /vrf red

C. telnet 11.1.1.4 /source vrf red

D. telnet 11.1.1.4 /vrf red

E. telnet 11.1.1.4 vrf red

Answer: D

Explanation:

Telnetting can be done through the VRF using the Management Ethernet interface. In the

following example, the router telnets to 172.17.1.1 through the Management Ethernet interface

VRF:

Router# telnet 172.17.1.1 /vrf Mgmt-intf

Reference

http://www.cisco.com/en/US/docs/routers/asr1000/configuration/guide/chassis/Management_Ether

net.html

CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.

400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand	Certbus	Testking	Pass4sure	Actualtests	Others
Price	$45.99	$124.99	$125.99	$189	$69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection