Free Providing CertBus Cisco 400-101 VCE Exam Study Guides With New Update Exam Questions

CertBus 2018 Newest Cisco 400-101 CCIE Exam VCE and PDF Dumps for Free Download!

☆ 400-101 CCIE Exam PDF and VCE Dumps : 1063QAs Instant Download: https://www.certgod.com/400-101.html [100% 400-101 Exam Pass Guaranteed or Money Refund!!]
☆ Free view online pdf on CertBus free test 400-101 PDF: https://www.certgod.com/online-pdf/400-101.pdf
☆ CertBus 2018 Newest 400-101 CCIE exam Question PDF Free Download from Google Drive Share: https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

Following 400-101 1063QAs are all new published by Cisco Official Exam Center

One of my colleague recommend me that CertBus CCIE Hotest 400-101 pdf dumps are effective and helpful. Thank goodness I followed up with him and choose CertBus as my assistance on my CCIE Hotest 400-101 QAs CCIE Routing and Switching Written v5.0 certification exam! I passed my Cisco CCIE Apr 02,2018 Latest 400-101 QAs exam very easily. I was lucky, all my questions in the exams were from my Cisco CCIE Latest 400-101 vce dumps.

CertBus latest 400-101 certification exam CertBus vce download. CertBus – help candidates on all 400-101 certification exams preparation. pass 400-101 certification exams, get it certifications easily. get 400-101 certification with CertBus study materials and practice tests. CertBus – your reliable partner and professional 400-101 certification exam material provider.

We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: https://www.certgod.com/400-101.html

QUESTION NO:1

Which two commands are required to enable multicast on a router, knowing that the receivers only

support IGMPv2? (Choose two.)

A. ip pim rp-address

B. ip pim ssm

C. ip pim sparse-mode

D. ip pim passive

Answer: A,C

Explanation:

Sparse mode logic (pull mode) is the opposite of Dense mode logic (push mode), in Dense mode

it is supposed that in every network there is someone who is requesting the multicast traffic so

PIM-DM routers begin by flooding the multicast traffic out of all their interfaces except those from

where a prune message is received to eliminate the

QUESTION NO:4

Refer to the exhibit.

R1 has an EBGP session to ISP 1 and an EBGP session to ISP 2. R1 receives the same prefixes

through both links.

Which configuration should be applied so that the link between R1 and ISP 2 will be preferred for

outgoing traffic (R1 to ISP 2)?

A. Increase local preference on R1 for received routes

B. Decrease local preference on R1 for received routes

C. Increase MED on ISP 2 for received routes

D. Decrease MED on ISP 2 for received routes

Answer: A

Explanation: Explanation

Local preference is an indication to the AS about which path has preference to exit the AS in order

to reach a certain network. A path with higher local preference is preferred more. The default value

of preference is 100.

Reference

http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080b82d1f.s

html?

referring_site=smartnavRD

QUESTION NO:8

Which statement is true about loop guard?

A. Loop guard only operates on interfaces that are considered point-to-point by the spanning tree.

B. Loop guard only operates on root ports.

C. Loop guard only operates on designated ports.

D. Loop guard only operates on edge ports.

Answer: A

Explanation:

Explanation

Understanding How Loop Guard Works

Unidirectional link failures may cause a root port or alternate port to become designated as root if

BPDUs are absent. Some software failures may introduce temporary loops in the network. Loop

guard checks if a root port or an alternate root port receives BPDUs. If the port is receiving

BPDUs, loop guard puts the port into an inconsistent state until it starts receiving BPDUs again.

Loop guard isolates the failure and lets spanning tree converge to a stable topology without the

failed link or bridge.

You can enable loop guard per port with the set spantree guard loop command.

Note When you are in MST mode, you can set all the ports on a switch with the set spantree

global-defaults loop-guard command.

When you enable loop guard, it is automatically applied to all of the active instances or VLANs to

which that port belongs. When you disable loop guard, it is disabled for the specified ports.

Disabling loop guard moves all loop-inconsistent ports to the listening state.

If you enable loop guard on a channel and the first link becomes unidirectional, loop guard blocks

the entire channel until the affected port is removed from the channel. Figure 8-6 shows loop

guard in a triangle switch configuration.

Figure 8-6 Triangle Switch Configuration with Loop Guard

Figure 8-6 illustrates the following configuration:

Switches A and B are distribution switches.

Switch C is an access switch.

Loop guard is enabled on ports 3/1 and 3/2 on Switches A, B, and C.

Use loop guard only in topologies where there are blocked ports. Topologies that have no blocked

ports, which are loop free, do not need to enable this feature. Enabling loop guard on a root switch

has no effect but provides protection when a root switch becomes a nonroot switch.

Follow these guidelines when using loop guard:

Do not enable loop guard on PortFast-enabled or dynamic VLAN ports.

Do not enable PortFast on loop guard-enabled ports.

Do not enable loop guard if root guard is enabled.

Do not enable loop guard on ports that are connected to a shared link.

Note: We recommend that you enable loop guard on root ports and alternate root ports on access

switches.

Loop guard interacts with other features as follows:

Loop guard does not affect the functionality of UplinkFast or BackboneFast.

Root guard forces a port to always be designated as the root port. Loop guard is effective only if

the port is a root port or an alternate port. Do not enable loop guard and root guard on a port at the

same time.

PortFast transitions a port into a forwarding state immediately when a link is established. Because

a PortFast-enabled port will not be a root port or alternate port, loop guard and PortFast cannot be

configured on the same port. Assigning dynamic VLAN membership for the port requires that the

port is PortFast enabled. Do not configure a loop guard-enabled port with dynamic VLAN

membership.

If your network has a type-inconsistent port or a PVID-inconsistent port, all BPDUs are dropped

until the misconfiguration is corrected. The port transitions out of the inconsistent state after the

message age expires. Loop guard ignores the message age expiration on type-inconsistent ports

and PVID-inconsistent ports. If the port is already blocked by loop guard, misconfigured BPDUs

that are received on the port make loop guard recover, but the port is moved into the type-

inconsistent state or PVID-inconsistent state.

In high-availability switch configurations, if a port is put into the blocked state by loop guard, it

remains blocked even after a switchover to the redundant supervisor engine. The newly activated

supervisor engine recovers the port only after receiving a BPDU on that port.

Loop guard uses the ports known to spanning tree. Loop guard can take advantage of logical ports

provided by the Port Aggregation Protocol (PAgP). However, to form a channel, all the physical

ports grouped in the channel must have compatible configurations. PAgP enforces uniform

configurations of root guard or loop guard on all the physical ports to form a channel.

These caveats apply to loop guard:

QUESTION NO:15

Which three options are considered in the spanning-tree decision process? (Choose three.)

A. lowest root bridge ID

B. lowest path cost to root bridge

C. lowest sender bridge ID

D. highest port ID

E. highest root bridge ID

F. highest path cost to root bridge

Answer: A,B,C

Explanation:

Configuration bridge protocol data units (BPDUs) are sent between switches for each port.

Switches use s four step process to save a copy of the best BPDU seen on every port. When a

port receives a better BPDU, it stops sending them. If the BPDUs stop arriving for 20 seconds

(default), it begins sending them again.

Step 1 Lowest Root Bridge ID (BID)

Step 2 Lowest Path Cost to Root Bridge

Step 3 Lowest Sender BID

Step 4 Lowest Port ID

Reference

Cisco General Networking Theory Quick Reference Sheets

QUESTION NO:19

Which two options does Cisco PfR use to control the entrance link selection with inbound

optimization? (Choose two.)

A. Prepend extra AS hops to the BGP prefix.

B. Advertise more specific BGP prefixes (longer mask).

C. Add (prepend) one or more communities to the prefix that is advertised by BGP.

D. Have BGP dampen the prefix.

Answer: A,C

Explanation: PfR Entrance Link Selection Control Techniques

The PfR BGP inbound optimization feature introduced the ability to influence inbound traffic. A

network advertises reachability of its inside prefixes to the Internet using eBGP advertisements to

its ISPs. If the same prefix is advertised to more than one ISP, then the network is multihoming.

PfR BGP inbound optimization works best with multihomed networks, but it can also be used with

a network that has multiple connections to the same ISP. To implement BGP inbound

optimization, PfR manipulates eBGP advertisements to influence the best entrance selection for

traffic bound for inside prefixes. The benefit of implementing the best entrance selection is limited

to a network that has more than one ISP connection.

To enforce an entrance link selection, PfR offers the following methods:

BGP Autonomous System Number Prepend When an entrance link goes out-of-policy (OOP) due

to delay, or in images prior to Cisco IOS Releases 15.2(1) T1 and 15.1(2)S, and PfR selects a

best entrance for an inside prefix, extra autonomous system hops are prepended one at a time (up

to a maximum of six) to the inside prefix BGP advertisement over the other entrances. In Cisco

IOS Releases 15.2(1)T1, 15.1(2)S, and later releases, when an entrance link goes out-of policy

(OOP) due to unreachable or loss reasons, and PfR selects a best entrance for an inside prefix,

six extra autonomous system hops are prepended immediately to the inside prefix BGP

advertisement over the other entrances. The extra autonomous system hops on the other

entrances increase the probability that the best entrance will be used for the inside prefix. When

the entrance link is OOP due to unreachable or loss reasons, six extra autonomous system hops

are added immediately to allow the software to quickly move the traffic away from the old entrance

link. This is the default method PfR uses to control an inside prefix, and no user configuration is

required.

BGP Autonomous System Number Community Prepend

When an entrance link goes out-of-policy (OOP) due to delay, or in images prior to Cisco IOS

Releases 15.2

(1)T1 and 15.1(2)S, and PfR selects a best entrance for an inside prefix, a BGP prepend

community is attached one at a time (up to a maximum of six) to the inside prefix BGP

advertisement from the network to another autonomous system such as an ISP. In Cisco IOS

Releases 15.2(1)T1, 15.1(2)S, and later releases, when an entrance link goes out-of-policy (OOP)

due to unreachable or loss reasons, and PfR selects a best entrance for an inside prefix, six BGP

prepend communities are attached to the inside prefix BGP advertisement. The BGP prepend

community will increase the number of autonomous system hops in the advertisement of the

inside prefix from the ISP to its peers. Autonomous system prepend BGP community is the

preferred method to be used for PfR BGP inbound optimization because there is no risk of the

local ISP filtering the extra autonomous system hops. There are some issues, for example, not all

ISPs support the BGP prepend community, ISP policies may ignore or modify the autonomous

system hops, and a transit ISP may filter the autonomous system path. If you use this method of

inbound optimization and a change is made to an autonomous system, you must issue an

outbound reconfiguration using the “clear ip bgp” command.

Reference

http://www.cisco.com/en/US/docs/ios-xml/ios/pfr/configuration/15-2s/pfr-bgp-inbound.html#GUID-

F8A59E241D59-

4924-827D-B23B43D9A8E0

http://www.cisco.com/en/US/products/ps8787/products_ios_protocol_option_home.html

400-101 PDF Dumps400-101 Study Guide400-101 Exam Questions

QUESTION NO:20

Refer to the exhibit.

What is the potential issue with this configuration?

A. There is no potential issue; OSPF will work fine in any condition.

B. Sub-optimal routing may occur since there is no area 1 adjacency between the ABRs.

C. This is a wrong OSPF configuration because all routers must be in area 0 only.

D. This is a wrong OSPF configuration because /30 requires 0.0.0.3 wild card.

Answer: B

Explanation:

QUESTION NO:21

Refer to the exhibit.

A packet from RTD with destination RTG, is reaching RTB. What is the path this packet will take

from RTB to reach RTG?

A. RTB – RTA – RTG

B. RTB – RTD – RTC – RTA – RTG

C. RTB – RTF – RTE – RTA – RTG

D. RTB will not be able to reach RTG since the OSPF configuration is wrong.

Answer: C

Explanation:

QUESTION NO:22

Refer to the exhibit.

Which path is selected as best path?

A. path 1, because it is learned from IGP B.

path 1, because the metric is the lowest C.

path 2, because it is external

D. path 2, because it has the higher router ID

Answer: B

Explanation:

QUESTION NO:29

What is the first thing that happens when IPv6 is enabled on an interface on a host?

A. A router solicitation is sent on that interface.

B. There is a duplicate address detection on the host interface.

C. The link local address is assigned on the host interface.

D. A neighbor redirect message is sent on the host interface.

Answer: B

Explanation:

Duplicate address detection (DAD) is used to verify that an IPv6 home address is unique on the

LAN before assigning the address to a physical interface (for example, QDIO). z/OS

Communications Server responds to other nodes doing DAD for IP addresses assigned to the

interface.

Reference

http://publib.boulder.ibm.com/infocenter/zos/v1r12/index.jsp?topic=/com.ibm.zos.r12.hale001

/ipv6d0021002145.htm

QUESTION NO:32

Which two tunneling techniques support IPv6 multicasting? (Choose two.)

A. 6to4

B. 6over4

C. ISATAP

D. 6PE

E. GRE

Answer: B,E

Explanation:

When IPv6 multicast is supported (over a 6to4 tunnel), an IPv6 multicast routing protocol must be

used

Restrictions for Implementing IPv6 Multicast

IPv6 multicast for Cisco IOS software uses MLD version 2. This version of MLD is fully backward-

compatible with MLD version 1 (described in RFC 2710). Hosts that support only MLD version 1

will interoperate with a router running MLD version 2. Mixed LANs with both MLD version 1 and

MLD version 2 hosts are likewise supported.

IPv6 multicast is supported only over IPv4 tunnels in Cisco IOS Release 12.3(2)T, Cisco IOS

Release 12.2

(18)S, and Cisco IOS Release 12.0(26)S.

When the bidirectional (bidir) range is used in a network, all routers in that network must be able to

understand the bidirectional range in the bootstrap message (BSM).

IPv6 multicast routing is disabled by default when the ipv6 unicast-routing command is configured.

On Cisco Catalyst 6500 and Cisco 7600 series routers, the ipv6 multicast-routing also must be

enabled in order to use IPv6 unicast routing

Reference http://www.cisco.com/web/about/ac123/ac147/ac174/ac197/

about_cisco_ipj_archive_article09186a00800c830a.html

http://www.cisco.com/en/US/docs/ios/ipv6/configuration/guide/ip6-multicast.html

https://supportforums.cisco.com/thread/183386

CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.

400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: https://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand	Certbus	Testking	Pass4sure	Actualtests	Others
Price	$45.99	$124.99	$125.99	$189	$69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection