Free Sharing CertBus Updated Cisco 400-101 VCE and PDF Exam Practice Materials

How to pass CCIE 400-101 exam 100% without any difficulties? We, CertBus, provide the latest exam preparation material for the Cisco 400-101 CCIE Routing and Switching Written v5.0 exam. Successful candidates share their experience about their CCIE 400-101 exam and the CCIE 400-101 exam preparation with CertBus exam Q and As. CertBus provides the new VCE and PDF dumps for the latest 400-101 exam. We ensure your CCIE 400-101 CCIE Routing and Switching Written v5.0 exam pass.

We CertBus has our own expert team. They selected and published the latest 400-101 preparation materials from Cisco Official Exam-Center: http://www.certgod.com/400-101.html

QUESTION NO:10

Which command is used to enable EtherChannel hashing for Layer 3 IP and Layer 4 port-based

CEF?

A. mpls ip cef

B. port-channel ip cef

C. mpls ip port-channel cef

D. port-channel load balance

E. mpls ip load-balance

F. ip cef EtherChannel channel-id XOR L4

G. ip cef connection exchange

Answer: D

Explanation:

QUESTION NO:42

Which type of domains is interconnected using Multicast Source Discovery Protocol?

A. PIM-SM

B. PIM-DM

C. PIM-SSM

D. DVMRP

Answer: A

Explanation: Multicast Source Discovery Protocol (MSDP) is a Protocol Independent Multicast

(PIM) family multicast routing protocol defined by Experimental RFC 3618. MSDP interconnects

multiple IPv4 PIM Sparse-Mode (PIM-SM) domains which enables PIM-SM to have Rendezvous

Point (RP) redundancy and inter-domain multicasting.

Reference

http://en.wikipedia.org/wiki/Multicast_Source_Discovery_Protocol

QUESTION NO:12

Which two options are contained in a VTP subset advertisement? (Choose two.)

A. followers field

B. MD5 digest

C. VLAN information

D. sequence number

Answer: C,D

Explanation:

Subset Advertisements

When you add, delete, or change a VLAN in a Catalyst, the server Catalyst where the changes are

made increments the configuration revision and issues a summary advertisement. One or several

subset advertisements follow the summary advertisement. A subset advertisement contains a list

of VLAN information.

If there are several VLANs, more than one subset advertisement can be required in order to

advertise all the VLANs.

Subset Advertisement Packet Format

This formatted example shows that each VLAN information field contains information for a different

VLAN. It is ordered so that lowered-valued ISL VLAN IDs occur first:

Most of the fields in this packet are easy to understand. These are two clarifications:

Code

QUESTION NO:27

Refer to the exhibit.

What triggered the first SPF recalculation?

A. changes in a router LSA, subnet LSA, and external LSA

B. changes in a router LSA, summary network LSA, and external LSA

C. changes in a router LSA, summary network LSA, and summary ASBR LSA

D. changes in a router LSA, summary ASBR LSA, and external LSA

Answer: B

Explanation:

OSPFv2

Is built around links, and any IP prefix change in an area will trigger a full SPF. It advertises IP

information in Router and Network LSAs. The routers thus, advertise both the IP prefix information

(or the connected subnet information) and topology information in the same LSAs. This implies

that if an IP address attached to an interface changes, OSPF routers would have to originate a

Router LSA or a Network LSA, which btw also carries the topology information. This would trigger

a full SPF on all routers in that area, since the same LSAs are flooded to convey topological

change information. This can be an issue with an access router or the one sitting at the edge,

since many stub links can change regularly.

Only changes in interarea, external and NSSA routes result in partial SPF calculation (since type

3, 4, 5 and 7 LSAs only advertise IP prefix information) and thus IS-IS

QUESTION NO:44

How is RPF used in multicast routing?

A. to prevent multicast packets from looping

B. to prevent PIM packets from looping

C. to instruct PIM where to send a (*, G) or (S, G) join message

D. to prevent multicast packets from looping and to instruct PIM where to send a (*, G) or (S, G)

join message

Answer: D

Explanation:

QUESTION NO:31

How will EIGRPv6 react if there is an IPv6 subnet mask mismatch between the Global Unicast

addresses on a point-to-point link?

A. EIGRPv6 will form a neighbor relationship.

B. EIGRPv6 will not form a neighbor relationship.

C. EIGRPv6 will form a neighbor relationship, but with the log MSG: “EIGRPv6 neighbor not on a

common subnet.”

D. EIGRPv6 will form a neighbor relationship, but routes learned from that neighbor will not be

installed in the routing table.

Answer: A Explanation:

http://www.ietf.org/rfc/rfc3587.txt

QUESTION NO:29

What is the first thing that happens when IPv6 is enabled on an interface on a host?

A. A router solicitation is sent on that interface.

B. There is a duplicate address detection on the host interface.

C. The link local address is assigned on the host interface.

D. A neighbor redirect message is sent on the host interface.

Answer: B

Explanation:

Duplicate address detection (DAD) is used to verify that an IPv6 home address is unique on the

LAN before assigning the address to a physical interface (for example, QDIO). z/OS

Communications Server responds to other nodes doing DAD for IP addresses assigned to the

interface.

Reference

http://publib.boulder.ibm.com/infocenter/zos/v1r12/index.jsp?topic=/com.ibm.zos.r12.hale001

/ipv6d0021002145.htm

QUESTION NO:34

In order to maintain security, with which hop count are IPv6 neighbor discovery packets sent?

A. 0

B. 1

C. 255

D. 256

Answer: C

Explanation:

QUESTION NO:20

Refer to the exhibit.

What is the potential issue with this configuration?

A. There is no potential issue; OSPF will work fine in any condition.

B. Sub-optimal routing may occur since there is no area 1 adjacency between the ABRs.

C. This is a wrong OSPF configuration because all routers must be in area 0 only.

D. This is a wrong OSPF configuration because /30 requires 0.0.0.3 wild card.

Answer: B

Explanation:

QUESTION NO:43

Which two multicast address ranges are assigned as source-specific multicast destination

addresses and are reserved for use by source-specific applications and protocols? (Choose two.)

A. 232.0.0.0/8

B. 239.0.0.0/8

C. 232.0.0.0/4

D. FF3x::/32

E. FF2x::/32

F. FF3x::/16

Answer: A,D

Explanation: Source-specific multicast (SSM) is a method of delivering multicast packets in which

the only packets that are delivered to a receiver are those originating from a specific source

address requested by the receiver. By so limiting the source, SSM reduces demands on the

network and improves security.

SSM requires that the receiver specify the source address and explicitly excludes the use of the (*,

G) join for all multicast groups in RFC 3376, which is possible only in IPv4’s IGMPv3 and IPv6’s

MLDv2.

Source-specific multicast is best understood in contrast to any-source multicast (ASM). In the

ASM service model a receiver expresses interest in traffic to a multicast address. The multicast

network must

1. discover all multicast sources sending to that address, and

2. route data from all sources to all interested receivers.

This behavior is particularly well suited to groupware applications where

1. all participants in the group want to be aware of all other participants, and

2. the list of participants is not known in advance.

The source discovery burden on the network can become significant when the number of sources

is large.

In the SSM service model, in addition to the receiver expressing interest in traffic to a multicast

address, the receiver expresses interest in receiving traffic from only one specific source sending

to that multicast address.

This relieves the network of discovering many multicast sources and reduces the amount of

multicast routing information that the network must maintain.

SSM requires support in last-hop routers and in the receiver’s operating system. SSM support is

not required in other network components, including routers and even the sending host. Interest in

multicast traffic from a specific source is conveyed from hosts to routers using IGMPv3 as

specified in RFC 4607.

SSM destination addresses must be in the ranges 232.0.0.0/8 for IPv4 or FF3x::/96 for IPv6.

Reference

http://en.wikipedia.org/wiki/Source-specific_multicast

CertBus exam braindumps are pass guaranteed. We guarantee your pass for the 400-101 exam successfully with our Cisco materials. CertBus CCIE Routing and Switching Written v5.0 exam PDF and VCE are the latest and most accurate. We have the best Cisco in our team to make sure CertBus CCIE Routing and Switching Written v5.0 exam questions and answers are the most valid. CertBus exam CCIE Routing and Switching Written v5.0 exam dumps will help you to be the Cisco specialist, clear your 400-101 exam and get the final success.

400-101 Latest questions and answers on Google Drive(100% Free Download): https://drive.google.com/file/d/0B_3QX8HGRR1mdEpkTFZvSDJDc2c/view?usp=sharing

400-101 Cisco exam dumps (100% Pass Guaranteed) from CertBus: http://www.certgod.com/400-101.html [100% Exam Pass Guaranteed]

Why select/choose CertBus?

Millions of interested professionals can touch the destination of success in exams by certgod.com. products which would be available, affordable, updated and of really best quality to overcome the difficulties of any course outlines. Questions and Answers material is updated in highly outclass manner on regular basis and material is released periodically and is available in testing centers with whom we are maintaining our relationship to get latest material.

Brand	Certbus	Testking	Pass4sure	Actualtests	Others
Price	$45.99	$124.99	$125.99	$189	$69.99-99.99
Up-to-Date Dumps
Free 365 Days Update
Real Questions
Printable PDF
Test Engine
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back
Secure Payment
Privacy Protection